Предусилитель, усилитель, фонокорректор и цифро-аналоговый преобразователь в одном корпусе. В сочетании с вашими любимыми колонками GSi75 обеспечит единственное и простое решение для управления вашей системой прослушивания. В отличие от других интегрированных моделей, GSi75 безкомпромиссный усилитель, созданный для реализации слушателем поставленных целей, обуздывая силу и технологии разработанные в Audio Research. Работая с новой лампой KT150, GSi75 снабжает звучание контролем и утонченностью, что обычно противоречит 75 Вт на канал номинальной мощности. Цифро-аналоговый преобразователь будет обрабатывать практически любую частоту дискретизации, в том числе и DSD. Фонокорректор и усилитель для наушников довершают оснощенность GSi75, обеспечивая гибкость интеграции в общую систему. Этот элегантный компонент, выполненный в промышленном дизайне, дополнит остальную часть вашей системы как визуально, так и акустически. Подробнее
Цена | 1 170 000 руб. |
Описание
OWER OUTPUT
75 watts per channel continuous from 20Hz to 20kHz. 1 kHz total harmonic distortion typically 1.5% at 75 watts, .05% at 1 watt. Approximate actual power available at “clipping” 80 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
POWER BANDWIDTH (-3dB points)
12Hz to 70kHz.
FREQUENCY RESPONSE (-3dB points at 1 watt)
1.0Hz to 70 kHz.
INPUT SENSITIVITY
0.55V RMS Single-ended for rated output. (32.5dB gain into 8 ohms.)
INPUT IMPEDANCE
52.5K ohms Single-ended.
INPUTS
SE1, SE2, SE3, Phono, S/PDIF digital (coax RCA and Toslink), USB
MAXIMUM INPUT
10V RMS (any input).
OUTPUT POLARITY
Non-Inverting (any input).
OUTPUT TAPS
8 ohms, 4 ohms.
OUTPUT REGULATION
Approximately 2dB 8 ohm load to open circuit (Damping factor approximately 4).
OVERALL NEGATIVE FEEDBACK
4dB.
SLEW RATE
10 volts/microsecond.
RISE TIME
4 microseconds.
HUM & NOISE
Less than 1.0 mV RMS -88dB below rated output (IHF weighted, Vol down).
CONTROLS
Rotary volume (103 steps), Rotary input selector, Power, Mute, Bias.
DIGITAL SAMPLE RATES
44.1kHz to 192kHz, SPDIF and USB 2.0 HS, DSD USB 2.0 HS
MASTER OSCILLATOR
22.579mHz ±20Hz for 44.1, 88.2 & 176.4kHz. 24.576mHz ±20Hz for 48, 96 & 192kHz sample rates.
INTRINSIC JITTER
<10ps
POWER SUPPLIES
Electronically regulated Low and High voltage supplies for input stages. Automatic 40 sec. warm-up/brown-out mute.
POWER SUPPLY ENERGY STORAGE
Approximately 350 joules.
POWER REQUIREMENTS100-125VAC 60Hz (200-250VAC 50Hz)
400 watts at rated output, 600 watts maximum, 210 watts at “idle’: 1.0 watt power off.
TUBES REQUIRED
2-Matched pair KT150-Power Output; 2 -6H30 driver.
75 watts per channel continuous from 20Hz to 20kHz. 1 kHz total harmonic distortion typically 1.5% at 75 watts, .05% at 1 watt. Approximate actual power available at “clipping” 80 watts (1kHz). (Note that actual power output is dependent upon both line voltage and “condition” i.e.: if power line has high distortion, maximum power will be affected adversely, although from a listening standpoint this is not very critical.)
POWER BANDWIDTH (-3dB points)
12Hz to 70kHz.
FREQUENCY RESPONSE (-3dB points at 1 watt)
1.0Hz to 70 kHz.
INPUT SENSITIVITY
0.55V RMS Single-ended for rated output. (32.5dB gain into 8 ohms.)
INPUT IMPEDANCE
52.5K ohms Single-ended.
INPUTS
SE1, SE2, SE3, Phono, S/PDIF digital (coax RCA and Toslink), USB
MAXIMUM INPUT
10V RMS (any input).
OUTPUT POLARITY
Non-Inverting (any input).
OUTPUT TAPS
8 ohms, 4 ohms.
OUTPUT REGULATION
Approximately 2dB 8 ohm load to open circuit (Damping factor approximately 4).
OVERALL NEGATIVE FEEDBACK
4dB.
SLEW RATE
10 volts/microsecond.
RISE TIME
4 microseconds.
HUM & NOISE
Less than 1.0 mV RMS -88dB below rated output (IHF weighted, Vol down).
CONTROLS
Rotary volume (103 steps), Rotary input selector, Power, Mute, Bias.
DIGITAL SAMPLE RATES
44.1kHz to 192kHz, SPDIF and USB 2.0 HS, DSD USB 2.0 HS
MASTER OSCILLATOR
22.579mHz ±20Hz for 44.1, 88.2 & 176.4kHz. 24.576mHz ±20Hz for 48, 96 & 192kHz sample rates.
INTRINSIC JITTER
<10ps
POWER SUPPLIES
Electronically regulated Low and High voltage supplies for input stages. Automatic 40 sec. warm-up/brown-out mute.
POWER SUPPLY ENERGY STORAGE
Approximately 350 joules.
POWER REQUIREMENTS100-125VAC 60Hz (200-250VAC 50Hz)
400 watts at rated output, 600 watts maximum, 210 watts at “idle’: 1.0 watt power off.
TUBES REQUIRED
2-Matched pair KT150-Power Output; 2 -6H30 driver.
